Looking at those pics. I'm thinking the same as the others. Maybe the idler is too large. I have a sb48 and the lever points up towards the chute. Not down like yours.
Sent from my SM-G975U using Tapatalk
Case 446, Broke Still !
-
Jancoe
- Posts: 326
- Joined: Sat Mar 06, 2021 3:09 pm
- Location: Houghton Lake, MI
- Has thanked: 16 times
- Been thanked: 1453 times
-
Eugen
- Posts: 5379
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 14077 times
- Been thanked: 17441 times
- Contact:
Re: Case 446, Broke Still !
Here Noel
The caster show is about 3" above ground and the bottom end of the lever is about 5" above ground. Hope this helps!
The caster show is about 3" above ground and the bottom end of the lever is about 5" above ground. Hope this helps!
Last edited by Eugen on Mon Jan 17, 2022 3:04 pm, edited 1 time in total.
-
Eugen
- Posts: 5379
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 14077 times
- Been thanked: 17441 times
- Contact:
Re: Case 446, Broke Still !
This one shows how high that tongue is, picture from back and ground level
You may have inherited a modified caster
You may have inherited a modified caster
Last edited by Eugen on Mon Jan 17, 2022 3:06 pm, edited 1 time in total.
-
DavidBarkey
- Posts: 4094
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 20648 times
- Been thanked: 15137 times
Re: Case 446, Broke Still !
@Propane57 Noel I measured the one off the caster I am working on and the V pulley 4" OC. / flat back 4.5" OC. Is your motor bolted to the frame or has it rubber mounts? If mounts how thick ? I beleave the belt for you set up is 1/2" x 81.625" . Now what is does not say if that is CL. or OC. I will assume it is OC. and if you have an after market belt that is an "81" , it may only measure 80.5" which would make it almost an inch to short . And if any of the other things I have mentioned come in to play ,that would make it even shorter forcing the arm to the ground .
Dave
Dave
Dave
Mad Tractor Builder
Mad Tractor Builder
-
propane1
- Posts: 2855
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 6799 times
- Been thanked: 10918 times
Re: Case 446, Broke Still !
Dave, the V stationary pulley is 4” outside diameter and flat idler pulley is 4.5 “ outside diameter. Motor looks to be bolted to the frame.
If any of have ever looked at how far the arm drops when you lift the thrower, it drops about 3”.
Noel
If any of have ever looked at how far the arm drops when you lift the thrower, it drops about 3”.
Noel
-
propane1
- Posts: 2855
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 6799 times
- Been thanked: 10918 times
-
DavidBarkey
- Posts: 4094
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 20648 times
- Been thanked: 15137 times
Re: Case 446, Broke Still !
Can you take off your belt . Make a mark on the outside. measure the circumference and see what the belt actually measures .
Dave
Dave
Mad Tractor Builder
Mad Tractor Builder
-
propane1
- Posts: 2855
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 6799 times
- Been thanked: 10918 times
-
DavidBarkey
- Posts: 4094
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 20648 times
- Been thanked: 15137 times
Re: Case 446, Broke Still !
Sorry bud thats all I can think to check . Maybe you ran over Murphy and it is his way of getting you back .
Dave
Dave
Mad Tractor Builder
Mad Tractor Builder
-
propane1
- Posts: 2855
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 6799 times
- Been thanked: 10918 times
Re: Case 446, Broke Still !
Oh well. I’ll get it Dave. May not be stock. But I’ll get it. Thanks for all your help.
Like I said before, if it’s gunna happen, it’s gunna happen to me. I always seem to get the odd ball stuff and or problems.
Noel
Like I said before, if it’s gunna happen, it’s gunna happen to me. I always seem to get the odd ball stuff and or problems.
Noel