Colt Case Ingersoll Garden Tractors

As winter slooowwwly and gladdlly comes to and end, my Case 446 will not have anything to do, as I only have the snow caster for it. So I’m hoping to get a sleeve hitch for it so I can use my sleeve hitch attachment that I have now, on it.
So three questions at the moment.
One: what tractor number sleeve hitch will fit my tractor. Mine is a 1982 model.
Two: will 200 series tractors fit.
Three: because the 400 series tractor are higher, will the sleeve hitch attachments I have now, that work on a garden tractor with 7” or so ground clearance work on the 446 with 11” of ground clearance.

Thanks for any information you can give.

Noel

Don't know about the other questions but the brinly plow I have was fine both on my 220 and the 446. Same with the tiller. I suppose there can be some minor difference but I was able to do garden work with both. then again, I'm not a purfectionist

Thanks Eugen.





Noel

The old forum had a what fits chart. Maybe we could borrow it... and maybe the chart to figure out what year your tractor is by serial number...

MattA wrote: ↑Mon Mar 07, 2022 5:29 pm The old forum had a what fits chart. Maybe we could borrow it... and maybe the chart to figure out what year your tractor is by serial number...

@Eugen Don't we have that here ?

Dave

The 200s use different than the 400s. I think a H, J, or K24 is what you should be looking for.

I also think there is plans to build your own.

I don't think the implements will matter, they were made to fit a wide variety of brands of tractors.

Timj wrote: ↑Mon Mar 07, 2022 6:24 pm The 200s use different than the 400s. I think a H, J, or K24 is what you should be looking for.

I also think there is plans to build your own.

I don't think the implements will matter, they were made to fit a wide variety of brands of tractors.

Thanks Tim.

Noel

Picture of the model plate.

Noel

Propane57 wrote: ↑Mon Mar 07, 2022 7:00 pm

Timj wrote: ↑Mon Mar 07, 2022 6:24 pm The 200s use different than the 400s. I think a H, J, or K24 is what you should be looking for.

I also think there is plans to build your own.

I don't think the implements will matter, they were made to fit a wide variety of brands of tractors.

Thanks Tim.

Noel

According to this, last page, the k24 is the one for you. The what fits chart wasn't totally clear. Maybe Bob @myerslawnandgarden will know for sure or what the real difference is, or if a H or J24 would work.

Jumpins, thanks again Tim.

Noel.

So, are you going to build one? : Or do you think you can find one, I'm guessing there is not alot of Case in your area.

Well the first thing will be to put ads out looking for one Tim. And your right, I doubt I’ll find one. But, someone a short while ago was looking for a mower deck for a Case. So slimly , there could be one here some where, but to find it !
Then I’ll check in the maritimes for one. I know a fella in Cape Breton , NS who is in to Case tractors, he may have one or know of one. So will see what happens.
May make one too.


Noel

I looked for the plans here could not find them, and on the other site the link to the pdf is missing But as I recall the sleeve hitch for the 4xx is 2-2.25 inches longer than the one for the 2xx's.


Gordy

Here's the link to the attachments fit chart

http://manuals.ccigt.com/More/cciAttachmentChart.pdf

@Gordy what"s the name of the file with the plans?

OOP's 4 inch difference, so much for my memory Thanks for finding the plans Eugen


Gordy

Timj wrote: ↑Mon Mar 07, 2022 7:18 pm

Propane57 wrote: ↑Mon Mar 07, 2022 7:00 pm

Timj wrote: ↑Mon Mar 07, 2022 6:24 pm The 200s use different than the 400s. I think a H, J, or K24 is what you should be looking for.

I also think there is plans to build your own.

I don't think the implements will matter, they were made to fit a wide variety of brands of tractors.

Thanks Tim.

Noel

According to this, last page, the k24 is the one for you.
Sleeve Hitch H, J, K 22 & 24 Manual 9-99726_watermarked.pdf

The what fits chart wasn't totally clear. Maybe Bob @myerslawnandgarden will know for sure or what the real difference is, or if a H or J24 would work.

Late to the party but a K24 is what would be needed for a long wheelbase 400 series tractor. That said, the only difference between the J24 and K24 is a 2" longer lift arm which either can be purchased new or the old one could be lengthened.

Bob

For what it is worth: I am in possession of a NOS sleeve hitch for the 200 or 3000 series tractors. It is the current reinforced sleeve hitch not the original version. It is very nice condition. Probably wouldn't be willing to ship to Canada, but if somebody wanted to meet me at Port Huron for coffee that might be arranged for fuel. I am 3 hours out from there. Or could meet in Detroit area 2 hours, but more hassle to exchange there.

And of course this would be a part for your "Tractor" !

If someone wants it, I can be flexible.

I have had it for a couple of years and I don't have anything but 400 or 4000 series tractors.

Bill Moyer
Coldwater, MI @ the bottom of the state along Interstate 69