These types of pulleys question.
- propane1
- Posts: 2450
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5815 times
- Been thanked: 8806 times
These types of pulleys question.
How do you get them apart to get the pulley off? I’ve seen these before at times. But have never worked with them. Are they original to this deck? And this deck goes on this tractor. I believe the deck is original to this tractor. 1975.
Thanks for any help.
Noel
Thanks for any help.
Noel
- Spike188
- Posts: 1074
- Joined: Sat Mar 06, 2021 12:58 pm
- Location: Ayr Ontario
- Has thanked: 5833 times
- Been thanked: 4144 times
Re: These types of pulleys question.
-Clean the push holes with a tap, the treads will have dirt in them and the bolt will jam before bottoming.
-Do not use an impact wrench when driving the bolts in for hub removal. Use and end wrench to feel torque and movement. Do the bolts in even torque.
-Do not over torque the bolt nearest the bushing split. This is the weakest part of the flange on the bushing. The flange can be broken off of the bushing. Give even pressure to both pusher bolts then tap the sheave lightly, torque some more if needed. Once sheave has dropped away from bushing insert your favorite screwdriver in the hub split to open the bushing slightly. The hub should slide easily off the shaft.
[youtube]https://www.youtube.com/watch?v=xWetOouz09M[/youtube]
This one can be a bit harder. A bearing separator is my preferred method on a stubborn pulley.
[youtube]www.youtube.com/watch?v=JRiMIorP-oQ[/youtube]
Others may have methods they use.
Hope this helps.
Spike.
Spike Colt - 9 & 10, Case - 108, 118, 444, 446, 448, 646, 646bh, Ingersoll 4016, 4118AH
- propane1
- Posts: 2450
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5815 times
- Been thanked: 8806 times
Re: These types of pulleys question.
Thanks spike. I don’t see any thread on the other two holes. But could be filled with dirt. And I wondered that. About taking the two bolts out and putting them in the other holes. But like I say, didn’t see any threads. And the pictures of these pulleys I looked at on Internet didn’t have any threads in those holes either.
I’ll get another look at it tomorrow. Thanks.
Noel.
I’ll get another look at it tomorrow. Thanks.
Noel.
- propane1
- Posts: 2450
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5815 times
- Been thanked: 8806 times
Re: These types of pulleys question.
Well I got it off. Cleaned out the other holes and put a tap through to clean it up. Took a little fighten to get it off. Any way give me a better look at things. Weird kind of a pulley.
Thanks fellas. Learn some thing every day. I’ll be some smart some day, but then to old to do anything.
Noel
Thanks fellas. Learn some thing every day. I’ll be some smart some day, but then to old to do anything.
Noel
- DavidBarkey
- Posts: 3147
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 17297 times
- Been thanked: 10642 times
Re: These types of pulleys question.
Somebody has some welding to do .
Dave
Dave
Dave
Mad Tractor Builder
Mad Tractor Builder
- propane1
- Posts: 2450
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5815 times
- Been thanked: 8806 times
- DavidBarkey
- Posts: 3147
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 17297 times
- Been thanked: 10642 times
Re: These types of pulleys question.
If you were closer I would just give you a deck . I have 3 extras
Dave
Dave
Mad Tractor Builder
Mad Tractor Builder
- propane1
- Posts: 2450
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5815 times
- Been thanked: 8806 times
- propane1
- Posts: 2450
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5815 times
- Been thanked: 8806 times
Re: These types of pulleys question.
Well, the deck is sorta fixed up so it’s useable. Hopefully. It really needs that whole section replaced. Which means getting all the parts out of there, cutting out all the old metal or making a piece to set over the top. Weld it in, then cut and drill all the holes to put it back together. A good metal worker could do that. I may or may not be able to do that. And still have it cut as good as it did last year. And I don’t have some of the tools to do it. And my welding is so, so. But maybe next winter I’ll try it. Have to start January 2/23 and not wait till April to start at it.
And I’m not showing any pictures of the sloppy repair I did to it. Please don’t ask
It would be better to find a good deck, but quite a job to find one here in PEI.
Have a good day gentlemen and have a great weekend.
Noel
And I’m not showing any pictures of the sloppy repair I did to it. Please don’t ask
It would be better to find a good deck, but quite a job to find one here in PEI.
Have a good day gentlemen and have a great weekend.
Noel
- Eugen
- Posts: 5166
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 12099 times
- Been thanked: 16346 times
- Contact:
Re: These types of pulleys question.
Noel, I have at least 2 spare deck housings in ok shape, too bad you're not closer.
Case 224, 444, 644, 680E
Kubota B26
Kubota B26