Fixing up my new 4020PS

Stuff about your Case, Colt, or Ingersoll tractor
User avatar
MattA United States of America
Posts: 1325
Joined: Sun Mar 07, 2021 1:57 pm
Location: Swansea MA
Has thanked: 5 times
Been thanked: 6027 times

Re: Fixing up my new 4020PS

Post by MattA »

I had the day off with the intention of using my 4020PS with the Johnny Bucket to clear the grass where the shed is going before another nor'Easter hits tomorrow and things didn't go as planned.

I found a small puddle of oil under the tractor which after removing the belly pan and tower screens I determined the first return line hose section after the oil filter was leaking. Tightening the hose clamps seems to have fixed the problem for now.

Today was the first time I ran the Linamar engine for more than a few minutes. The engine is surging a bit again. Raising the throttle a little + a little choke seemed to help. While the power steering worked great, it was a struggle to dig up the grass with the Johnny Bucket. Plenty of traction but the tractor just didn't push the bucket as well as I thought it should.

I left the tractor in the yard and took a quick lunch and came back to a tractor that wouldn't start. It cranks fine. I decided its punishment was to be towed to the garage by a vanguard.
Waiting for a tow
20261111_131552.jpg
Vanguard powered tow rig arrived
20261111_135753.jpg
It took a few minutes but I did get it to the garage. I discovered I could turn the 4020PS steering wheel a little to help direct it to the garage (non-running tractor with power steering).

Mowing deck came off the 4016. Johnny Bucket and the weights were swapped over.
20261111_154840.jpg
Before heading out with the 4016, I put a pair of Oregon spark testers inline with the Linamar's plugs and gave it a good cranking. The Linamar actually started and ran poorly. IMO the spark looks weak on both plugs. I could not start the Linamar on one plug or the other. That's where I quit the diagnosis for the day. I think I have an Onan service manual on pdf.

My 4016 did well with the Johnny Bucket. It's definitely got more pushing power than the 4020PS. I wasn't able to finish the job today. That's just how things go these days.
20261111_170220.jpg
I have to say I'm pretty discouraged with the 4020PS. I've spent a lot of time working on it and it still needs more work. I don't think I've put 2hrs on it yet.
Ingersoll 4016
User avatar
DavidBarkey Canada
Posts: 4228
Joined: Sat Mar 06, 2021 10:35 am
Location: Waverley On.
Has thanked: 21091 times
Been thanked: 15660 times

Re: Fixing up my new 4020PS

Post by DavidBarkey »

Working bugs of something that has sat for a time can be frustrating . Those twins use a waist spark system . Both plug need to be grounded for spark . Make sure you have solid battery voltage to the coil . I am assuming that this engine has electronic ignition . Condencer can go bad on these as well . Point = condencer on negative side of coil or at the points . Electronic = condencer on possitive side of coil .
image.png
With one side hooked up the other side should be able to jump a 1/4" gap in free air . These are cheap and handy .
image.png
image.png (581.67 KiB) Viewed 4975 times
Ohm out between both heads and block , plugs need a good ground and sometimes with age the head can lose a good ground through head bolts.
happy hunting
Dave
Mad Tractor Builder
User avatar
MattA United States of America
Posts: 1325
Joined: Sun Mar 07, 2021 1:57 pm
Location: Swansea MA
Has thanked: 5 times
Been thanked: 6027 times

Re: Fixing up my new 4020PS

Post by MattA »

Thanks David.

My understanding is the Linamar engines are equivalent to the Onan P series engines.

LX770 = P218G
LX790 = P220G
LX990 = P224G
Ingersoll 4016
User avatar
MattA United States of America
Posts: 1325
Joined: Sun Mar 07, 2021 1:57 pm
Location: Swansea MA
Has thanked: 5 times
Been thanked: 6027 times

Re: Fixing up my new 4020PS

Post by MattA »

I partially reassembled RM48 decks 3 & 4 today and replaced the belt tensioner pivot bushings and washers. Paint will have to wait for the spring.

I've got a new ignition condenser and some other parts coming in the mail tomorrow.

I measured the ignition coil primary and secondary resistance. The service manual lists the primary side as 2.9 to 3.6 ohms and the secondary side as 14500 to 19800 ohms when measured at 70F.

My 30 year old digital multimeter measured 3.3 ohms and 20090 ohms which is just out of spec. Today I got out my Keithley 2000 digital multimeter with 6.5 digits of precision + a recent calibration and the results weren't what I'd hoped they would be. 3.38 ohms and 20675 ohms. The 3.38 number includes the resistance of the meter probes.

I'll start with the condenser and new plug wires and see what happens.
Ingersoll 4016
User avatar
MattA United States of America
Posts: 1325
Joined: Sun Mar 07, 2021 1:57 pm
Location: Swansea MA
Has thanked: 5 times
Been thanked: 6027 times

Re: Fixing up my new 4020PS

Post by MattA »

Parts didn't arrive today so I decided to change the fuel filter. It took probably 20 minutes to drain about 2 gallons of gas. Eventually I figured out the fuel line was pinched between the engine shroud and the frame rail. I'm not sure if the old fuel filter or the pinched fuel line was limiting the flow. I do think the fuel line could be routed out where the power steering lines come out of the chassis. Anybody know where the fuel line is supposed to route? I checked the sale pictures and based on the existing fuel line routing, the fuel line was likely pinched when I bought the tractor. I also replaced the fuel filter to fuel pump hose since the hose was stuck on the filter. I may replace the fuel pump to carb fuel hose when I've got that apart replacing the condenser.

Old and new fuel filters
20261121_161631.jpg
Pinched fuel line
20261121_165659.jpg
New fuel filter and fuel hose
20261121_172818.jpg
Better place to run the fuel line?
20261121_170726.jpg
Ingersoll 4016
myerslawnandgarden United States of America
Posts: 391
Joined: Sun Mar 07, 2021 12:17 pm
Location: Hinckley, IL
Has thanked: 200 times
Been thanked: 2038 times

Re: Fixing up my new 4020PS

Post by myerslawnandgarden »

I'll give you odds that throwing plug wires and the condenser to it will make no difference.

If it's an ignition system problem, 99 times out of 100 it's the trigger module under the flywheel. They fail with regularity and are often intermittent / erratic. There is a test procedure in the service manual, if you can't find it I can send it to you.

Bob
Post Reply