The morning was spent on machine repairs. No photos, but got the MF-202 lower radiator hose replaced. Also repaired a couple minor item on the new to me MF-20C Turf.
After that, it was on to the stone slab that my rear staairs are going to land on.
Cue the 646 BH. I needed a hole that was perhaps 18" by 54". The slab is 14" x 48". You can't do precision digging here due to the rocks. The hole was probably 30" by 60".
Almost 12" of 2b gravel in the bottom as I don't want any drainage issues under the slab. Below the gravel is the weired bottomless pile of rocks I live on, so not likely to ever be an issue.
Bluestone slab in and back-filled. It's pitched just a touch away from the house, and also a little downhill. The stairs are just going to sit on it, so even if it moves a little, the stairs will be fine.
Next time I take a week off, I hope to be able to get some stairs landed there.
The Projects Never End
-
Toolslinger
- Posts: 486
- Joined: Wed Mar 03, 2021 12:03 pm
- Location: NJ/PA
- Has thanked: 29 times
- Been thanked: 2441 times
-
DavidBarkey
- Posts: 4226
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 21083 times
- Been thanked: 15656 times
Re: The Projects Never End
@Toolslinger That big pile of rocks are mostly likely granite from Canada . Your welcome . 
Dave
Mad Tractor Builder
Mad Tractor Builder
-
Toolslinger
- Posts: 486
- Joined: Wed Mar 03, 2021 12:03 pm
- Location: NJ/PA
- Has thanked: 29 times
- Been thanked: 2441 times
Re: The Projects Never End
I didn't get backl to the steps really until early October, but they're there now. Thought I had a photo, but can't find it. Will have to take another...
Last year, I had my old EZ-Rake blower take a fatal chunk of something in. This time it wedged hard enough to bend the output shaft of the Kohler. So, I found someone selling a Trac-Vac 3 point mount unit. It has been around the block. I put it on the 8N last year to finish up, and because the 8N doesn't have quite standard 3pt dimensions, I had to do some adapting... It got me through, but one the last load, one of the belts broke.
Fast forward to this year... I had picked up a new to me MF20C tractor. It was down most of the summer while I had a port in the head repaired. In the time between I had pulled the whole vac apart to replace the belts. That is an unfriendly design for service, and belt tensioning. If I had to start over on it, I would change some things to make it easier, but hopefully it will not chew up the belts now that I got everything in line. The belt guards are what came on it (obviously not OEM), and need to be improved for serviceability, but they're functional currently.
I will be replacing the black hose sections for next season as they are original, and really starting to shred. I have a better condition box to go on the trailer next season (box is rotted, and the top is really beat)... However, this setup was an absolute monster on the leaves this year. Big difference between a 5 horse 6" blower, and an 8" driven by 40 something...
In Case news, the 444 is ready for winter with the blower, chains, and counterweight. The 646BH has possibly one more dig this year if the weather lines up with my availability, but it's low priority. I keep arguing with myself to sell the other 646, but with the seasonal change, it wouldn't be a good time to sell anyway, so it's back in the barn with another reprieve...
Other work has been slowly trying to sell off some of the clutter that is still left from my father, and now starting to pick away at some of my own projects that are never going to happen to free up space for the things I do use... I am really tired of living with no floor space considering the amount of square feet I have...
Last year, I had my old EZ-Rake blower take a fatal chunk of something in. This time it wedged hard enough to bend the output shaft of the Kohler. So, I found someone selling a Trac-Vac 3 point mount unit. It has been around the block. I put it on the 8N last year to finish up, and because the 8N doesn't have quite standard 3pt dimensions, I had to do some adapting... It got me through, but one the last load, one of the belts broke.
Fast forward to this year... I had picked up a new to me MF20C tractor. It was down most of the summer while I had a port in the head repaired. In the time between I had pulled the whole vac apart to replace the belts. That is an unfriendly design for service, and belt tensioning. If I had to start over on it, I would change some things to make it easier, but hopefully it will not chew up the belts now that I got everything in line. The belt guards are what came on it (obviously not OEM), and need to be improved for serviceability, but they're functional currently.
I will be replacing the black hose sections for next season as they are original, and really starting to shred. I have a better condition box to go on the trailer next season (box is rotted, and the top is really beat)... However, this setup was an absolute monster on the leaves this year. Big difference between a 5 horse 6" blower, and an 8" driven by 40 something...
In Case news, the 444 is ready for winter with the blower, chains, and counterweight. The 646BH has possibly one more dig this year if the weather lines up with my availability, but it's low priority. I keep arguing with myself to sell the other 646, but with the seasonal change, it wouldn't be a good time to sell anyway, so it's back in the barn with another reprieve...
Other work has been slowly trying to sell off some of the clutter that is still left from my father, and now starting to pick away at some of my own projects that are never going to happen to free up space for the things I do use... I am really tired of living with no floor space considering the amount of square feet I have...