Hello from Ottawa, Ontario - "new" 4016

Please introduce yourself, your location, interests, etc.
User avatar
Harry United States of America
Posts: 1483
Joined: Sun Mar 07, 2021 8:33 am
Location: Lockport,NY
Has thanked: 9141 times
Been thanked: 6196 times

Re: Hello from Ottawa, Ontario - "new" 4016

Post by Harry »

Welcome to the CCIGT site Freddy. I saw your post on the original site and it's a pleasure to have you here also. Your 4016 looks very nice thanks for posting the pics. Very knowledable members here, so if you have any questions fire away.

Keep the :peace: :cop:
Harry
1973 444, 1974 644, 1976 446, 1977 646, 1986 226
User avatar
MattA United States of America
Posts: 859
Joined: Sun Mar 07, 2021 1:57 pm
Location: Swansea MA
Has thanked: 2 times
Been thanked: 3586 times

Re: Hello from Ottawa, Ontario - "new" 4016

Post by MattA »

Looks like my engine code is also 01.

Here is my transaxle. As far as I know the webbing is cast in. I've seen some older backhoe transaxles with smaller webbing. This late model transaxle has the updated differential and slightly different gearing. It's slightly faster in low range and slightly slower in high range.
Attachments
20170310_200017.jpg
20170310_200054.jpg
Ingersoll 4016
User avatar
MattA United States of America
Posts: 859
Joined: Sun Mar 07, 2021 1:57 pm
Location: Swansea MA
Has thanked: 2 times
Been thanked: 3586 times

Re: Hello from Ottawa, Ontario - "new" 4016

Post by MattA »

When you get around to it, change the transaxle oil. There is some info around on the weight and fill levels. The side of the transaxle has two pipe plugs with square heads. The upper one is to check the fill level, the lower is the drain. The older case tractors had higher fill levels and some people fill the newer transaxle to a higher level. I filled mine to the plug level in the rear by the hitch. The other members here might have some more info/opinions.
Ingersoll 4016
FreddyFont Canada
Posts: 46
Joined: Thu Nov 10, 2022 8:34 pm
Location: Ottawa,Ontario
Has thanked: 16 times
Been thanked: 215 times

Re: Hello from Ottawa, Ontario - "new" 4016

Post by FreddyFont »

I did change the transaxle oil, filled it up to the check bolt but I did see some owners are filling it right up to the top. I followed what was recommended in the owners manual. I used 80w90 since I had some on hand. Planning to run it for a bit then changing it again in case there was left over of the old oil in there. Will do the same for the engine and hydraulic oil.
User avatar
MattA United States of America
Posts: 859
Joined: Sun Mar 07, 2021 1:57 pm
Location: Swansea MA
Has thanked: 2 times
Been thanked: 3586 times

Re: Hello from Ottawa, Ontario - "new" 4016

Post by MattA »

Some other things I recommend doing are:
1. Adjusting the steering gear shims to tighten the steering up.
2. Replacing the front axle pin with one sold by xetta on ebay. What a difference that makes. I wish I had spent the money sooner. My steering may have been looser due to having the snowcaster on the front.
3. Look up poor man's power steering. For $20-30 this makes the tractor much easier to steer especially with the snowcaster lifted up.
Ingersoll 4016
FreddyFont Canada
Posts: 46
Joined: Thu Nov 10, 2022 8:34 pm
Location: Ottawa,Ontario
Has thanked: 16 times
Been thanked: 215 times

Re: Hello from Ottawa, Ontario - "new" 4016

Post by FreddyFont »

Thanks for the info, ill look into it. Not sure I fully get your first item its a mix of not being super mechanically inclined and speaking French. Not that I would know what you're talking about anyway ;)
User avatar
MattA United States of America
Posts: 859
Joined: Sun Mar 07, 2021 1:57 pm
Location: Swansea MA
Has thanked: 2 times
Been thanked: 3586 times

Re: Hello from Ottawa, Ontario - "new" 4016

Post by MattA »

FreddyFont wrote: Sat Nov 12, 2022 12:07 pm Thanks for the info, ill look into it. Not sure I fully get your first item its a mix of not being super mechanically inclined and speaking French. Not that I would know what you're talking about anyway ;)
I put together some info:
viewtopic.php?f=4&t=1127

I told @Eugen that I would do this like a year ago :cheers:
Ingersoll 4016
User avatar
Eugen Canada
Posts: 5139
Joined: Wed Mar 03, 2021 2:52 pm
Location: Port Mcnicoll, Ontario
Has thanked: 11932 times
Been thanked: 16180 times
Contact:

Re: Hello from Ottawa, Ontario - "new" 4016

Post by Eugen »

MattA wrote: Sat Nov 12, 2022 10:36 pm
I told @Eugen that I would do this like a year ago :cheers:
Thank you! :cheers:
Case 224, 444, 644, 680E
Kubota B26 :blush:
FreddyFont Canada
Posts: 46
Joined: Thu Nov 10, 2022 8:34 pm
Location: Ottawa,Ontario
Has thanked: 16 times
Been thanked: 215 times

Re: Hello from Ottawa, Ontario - "new" 4016

Post by FreddyFont »

Thanks for the write up! Very well explained with the reference to the picture I feel I'd be able to tackle this. I had looked at that YouTube video for the axle pin. Will get the parts over the winter and might wait for spring to install it all. Its getting cold outside and I'm not done finishing the garage interior.... too many projects lol!
User avatar
DavidBarkey Canada
Posts: 3106
Joined: Sat Mar 06, 2021 10:35 am
Location: Waverley On.
Has thanked: 17059 times
Been thanked: 10405 times

Re: Hello from Ottawa, Ontario - "new" 4016

Post by DavidBarkey »

@FreddyFont
Quote : too many projects lol!
You will fit in just fine here . :giggle:
Dave
Mad Tractor Builder
Post Reply