Linde 225 MIG welder in bad shape
- Spike188
- Posts: 1195
- Joined: Sat Mar 06, 2021 12:58 pm
- Location: Ayr Ontario
- Has thanked: 7259 times
- Been thanked: 4721 times
Re: Linde 225 MIG welder in bad shape
Just makes you want to spit and spew when that happens. Better luck on the next round. I didn't do the math but with larger capacity caps installed, can you get by with 3 caps?
Spike Colt - 9 & 10, Case - 108, 118, 444, 446, 448, 646, 646bh, Ingersoll 4016, 4118AH
-
- Posts: 5280
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 12888 times
- Been thanked: 16930 times
- Contact:
Re: Linde 225 MIG welder in bad shape
True! Yes, the forth one even didn't behave that nicely when I reformed it. It was hungry to draw a lot of current for too long, instead of charging nicely. Anyway, the three of them left are 16,000uF each, which is just 2000uF less than the original total capacity. And they didn't get warm at all while testing the welder on scrap.
So, yes, I decided to hook it up to welding gas and give it a proper try. Tested this MIG welder on various heat and wire speed settings and it sparkles just fine. The only slight problem is that the wire gets occasionally stuck in the cable of the gun. It's the only solid wire I got now (0.035), is rusty, and the gun and cable are really beat up, so this requires some attention.
However, right now it looks like this Linde 225 MIG welder has been saved from scrap and this makes me quite content.
- DavidBarkey
- Posts: 3426
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 18666 times
- Been thanked: 11974 times
Re: Linde 225 MIG welder in bad shape
You will have a real nice welder when you are done .
Dave
Mad Tractor Builder
Mad Tractor Builder
-
- Posts: 325
- Joined: Sat Mar 06, 2021 3:09 pm
- Location: Houghton Lake, MI
- Has thanked: 16 times
- Been thanked: 1446 times
Re: Linde 225 MIG welder in bad shape
Just a little tip for the mig welder. Seeing how you have some rusty wire. I use a clip on wire cleaner. You could use just about anything like foam ear plugs or felt with a paper clamp. Keeping the debris out of the liner is the goal. Hope this helps.
Sent from my SM-S906U using Tapatalk
Sent from my SM-S906U using Tapatalk
-
- Posts: 5280
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 12888 times
- Been thanked: 16930 times
- Contact:
Re: Linde 225 MIG welder in bad shape
Thank you @Gordy !
Yes Dave, I think you're right. I must say right now it seems a little too sophisticated a device for a beginner like me. I felt very comfortable with the stick welder and if I convert it to DC it'll probably be even nicer. So...
- Harry
- Posts: 1770
- Joined: Sun Mar 07, 2021 8:33 am
- Location: Lockport,NY
- Has thanked: 10808 times
- Been thanked: 7601 times
Re: Linde 225 MIG welder in bad shape
I have seen a scotch brite pad held on the wire with a clip to take the rust of the wire.
Keep the
Harry
Keep the
Harry
1973 444, 1974 644, 1976 446, 1977 646, 1986 226
- DavidBarkey
- Posts: 3426
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 18666 times
- Been thanked: 11974 times
Re: Linde 225 MIG welder in bad shape
I do the same with a piece of rag to keep the wire clean . Does a good job .
Dave
Mad Tractor Builder
Mad Tractor Builder