HarryRobber edge for snow blades
-
Harry
- Posts: 1512
- Joined: Sun Mar 07, 2021 8:33 am
- Location: Lockport,NY
- Has thanked: 9385 times
- Been thanked: 6344 times
Robber edge for snow blades
I seen this posted on the Buffalo, NY CL. I looks like it would be a good idea. Harry
Harry- Attachments
-
1973 444, 1974 644, 1976 446, 1977 646, 1986 226
-
Eugen
- Posts: 5165
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 12083 times
- Been thanked: 16330 times
- Contact:
Re: Robber edge for snow blades
Good if you have a paved driveway right?
Case 224, 444, 644, 680E
Kubota B26
Kubota B26
-
Timj
- Posts: 1444
- Joined: Thu Mar 04, 2021 9:57 pm
- Location: Central WI
- Has thanked: 5219 times
- Been thanked: 5028 times
Re: Robber edge for snow blades
The rubber edges have become quite popular even on larger plows, it's surprising how well they hold up. And no gouged and scratched up concrete or blacktop.
let's go, it's finally time to blow. -
myerslawnandgarden
- Posts: 227
- Joined: Sun Mar 07, 2021 12:17 pm
- Location: Hinckley, IL
- Has thanked: 104 times
- Been thanked: 1175 times
Re: Robber edge for snow blades
30 or so years ago when I sold a tractor/cab/blade combination to a company that had the snow removal contract for the Federal Building in Chicago, that was one of the requirements as the entire plaza at that address is marble. At the time poly or rubber edges were not that common, I ended up sourcing one from John Deere as they had a 54" blade as well.
Bob
Bob
-
DavidBarkey
- Posts: 3145
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 17282 times
- Been thanked: 10613 times
Re: Robber edge for snow blades
Has anyone tried them on snow casters ? Anyone use them on gravel ? I wounder if they would "dig in less ?
Dave
Mad Tractor Builder
Mad Tractor Builder
-
Timj
- Posts: 1444
- Joined: Thu Mar 04, 2021 9:57 pm
- Location: Central WI
- Has thanked: 5219 times
- Been thanked: 5028 times
Re: Robber edge for snow blades
Most of the rubber ones are thicker, with how the cutting edge is mounted on the caster, I think it might be hard to get it to not push snow ahead of the caster. Type of snow will play.DavidBarkey wrote: ↑Thu Jan 25, 2024 6:09 am Has anyone tried them on snow casters ? Anyone use them on gravel ? I wounder if they would "dig in less ?
A piece of thin high tech plastic may be a better choice, or even just on the shoes.
Last edited by Timj on Thu Jan 25, 2024 4:50 pm, edited 1 time in total.
let's go, it's finally time to blow. -
Toolslinger
- Posts: 298
- Joined: Wed Mar 03, 2021 12:03 pm
- Location: NJ/PA
- Has thanked: 23 times
- Been thanked: 1435 times
Re: Robber edge for snow blades
My father ran UHMW blocks for skids on the JD140 to avoid scratching his then new pavers. Took the chains off too, but that's another issue...
The blocks did ok, but over time they ground down far more quickly than the steel feet would. I went back to the steel as soon as I could. I could see using it across the whole bottom as the scraper and holding up quite a while as the load is far more distributed. The load on just the feet was really too much. The JD scrapper is probably 5/8" tall (kinda a channel with 45 deg sides) so there's enough room under there for something kinda thick. I haven't flipped a Case caster over to look at our scraper bar setup...
The blocks did ok, but over time they ground down far more quickly than the steel feet would. I went back to the steel as soon as I could. I could see using it across the whole bottom as the scraper and holding up quite a while as the load is far more distributed. The load on just the feet was really too much. The JD scrapper is probably 5/8" tall (kinda a channel with 45 deg sides) so there's enough room under there for something kinda thick. I haven't flipped a Case caster over to look at our scraper bar setup...