Kohler k321 static timing.

Troubleshooting, rebuilding, repairing Kohler engines.
User avatar
propane1 Canada
Posts: 2426
Joined: Thu Dec 23, 2021 11:32 am
Location: PEI, Canada
Has thanked: 5740 times
Been thanked: 8669 times

Re: Kohler k321 static timing.

Post by propane1 »

Well that could be Dave. The rod broke because the oiler hole to the crank was not pointing to the cam. Just hard to say what was done to the engine over its life time. Never thought of that breaking the key, when it stopped working. I did think the flywheel could be on wrong thou. But it did run before breaking the rod. The points, when I first started at this foolishness, were set wide. I’d say about 0.030. And like I say, it was running to break the rod.

Noel
User avatar
DavidBarkey Canada
Posts: 3108
Joined: Sat Mar 06, 2021 10:35 am
Location: Waverley On.
Has thanked: 17070 times
Been thanked: 10411 times

Re: Kohler k321 static timing.

Post by DavidBarkey »

Propane57 wrote: Tue Mar 15, 2022 7:49 am Well that could be Dave. The rod broke because the oiler hole to the crank was not pointing to the cam. Just hard to say what was done to the engine over its life time. Never thought of that breaking the key, when it stopped working. I did think the flywheel could be on wrong thou. But it did run before breaking the rod. The points, when I first started at this foolishness, were set wide. I’d say about 0.030. And like I say, it was running to break the rod.

Noel
I have always found , that when ever you have a situation where you you just can't get something adjusted to start checking all related components. As always let us know what you find .

Dave
Dave
Mad Tractor Builder
User avatar
propane1 Canada
Posts: 2426
Joined: Thu Dec 23, 2021 11:32 am
Location: PEI, Canada
Has thanked: 5740 times
Been thanked: 8669 times

Re: Kohler k321 static timing.

Post by propane1 »

Will do Dave. Thanks.

Noel
User avatar
propane1 Canada
Posts: 2426
Joined: Thu Dec 23, 2021 11:32 am
Location: PEI, Canada
Has thanked: 5740 times
Been thanked: 8669 times

Re: Kohler k321 static timing.

Post by propane1 »

Hehe. More trouble. Governor spring and arm worn bad. :35: Nothing to do with my timing trouble thou.

Noel
User avatar
propane1 Canada
Posts: 2426
Joined: Thu Dec 23, 2021 11:32 am
Location: PEI, Canada
Has thanked: 5740 times
Been thanked: 8669 times

Re: Kohler k321 static timing.

Post by propane1 »

Looks like you were right Dave.


Noel
Attachments
F7E3FCB7-C06D-4483-8C8E-D3235F6D847D.jpeg
User avatar
propane1 Canada
Posts: 2426
Joined: Thu Dec 23, 2021 11:32 am
Location: PEI, Canada
Has thanked: 5740 times
Been thanked: 8669 times

Re: Kohler k321 static timing.

Post by propane1 »

So of course I had no puller. It’s at my sons place. :pullhair: :(( :35: so I try the old three screw driver pry trick. Might have worked but got thinking. Found other small wrong puller and rigged it up. Didn’t take long to get the flywheel off. Thought it would have been harder because of the sheared key. Any way. It’s off, but !


Noel
Attachments
B50FCC9D-6535-4780-A9B7-AA5918A23DAE.jpeg
C59C63C0-D153-45D3-9F6A-53BEDC19A838.jpeg
9B0BAC3D-7A77-42DF-9825-F59BBA917104.jpeg
User avatar
propane1 Canada
Posts: 2426
Joined: Thu Dec 23, 2021 11:32 am
Location: PEI, Canada
Has thanked: 5740 times
Been thanked: 8669 times

Re: Kohler k321 static timing.

Post by propane1 »

So after getting the flywheel off, I see loose magnets :45: So what do I use to glue them back on ?


Noel
Attachments
6AB471DC-DA99-4734-A796-578AA5A051D5.jpeg
14C16DD3-049D-401C-BD26-FED48BB4EFC6.jpeg
3A5EBFA7-0BE2-409F-B6D1-A6403464AA89.jpeg
User avatar
Eugen Canada
Posts: 5141
Joined: Wed Mar 03, 2021 2:52 pm
Location: Port Mcnicoll, Ontario
Has thanked: 11934 times
Been thanked: 16194 times
Contact:

Re: Kohler k321 static timing.

Post by Eugen »

Propane57 wrote: Tue Mar 15, 2022 10:12 am Looks like you were right Dave.


Noel
Crazy! :O :109:
Case 224, 444, 644, 680E
Kubota B26 :blush:
User avatar
Eugen Canada
Posts: 5141
Joined: Wed Mar 03, 2021 2:52 pm
Location: Port Mcnicoll, Ontario
Has thanked: 11934 times
Been thanked: 16194 times
Contact:

Re: Kohler k321 static timing.

Post by Eugen »

Propane57 wrote: Tue Mar 15, 2022 11:38 am So after getting the flywheel off, I see loose magnets :45: So what do I use to glue them back on ?


Noel
Others may know better but I once glued a spark plug in the engine after it got spit out because some genius torqued it too much and broke the threads. With jb weld and it lasted another month until I fixed the thread. It was on a crown vic who did not mind running on 7 cylinders only. I know if no better glue for metal to metal.
Case 224, 444, 644, 680E
Kubota B26 :blush:
User avatar
Harry United States of America
Posts: 1483
Joined: Sun Mar 07, 2021 8:33 am
Location: Lockport,NY
Has thanked: 9159 times
Been thanked: 6197 times

Re: Kohler k321 static timing.

Post by Harry »

I agree JB weld works well!

Keep the Peace
Harry
1973 444, 1974 644, 1976 446, 1977 646, 1986 226
Post Reply