k301 stalling
- DavidBarkey
- Posts: 3175
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 17454 times
- Been thanked: 10775 times
k301 stalling
K301 will start and run great for 20 min. and then stumbles dies . Coil and condenser have been replaced . Good voltage out of the starter/generator . What are your ideas guys?
Dave
Mad Tractor Builder
Mad Tractor Builder
-
- Posts: 324
- Joined: Sat Mar 06, 2021 3:09 pm
- Location: Houghton Lake, MI
- Has thanked: 16 times
- Been thanked: 1438 times
Re: k301 stalling
My guess is coil acting up or exhaust valve getting hot and valve sticking open?
Sent from my SM-S906U using Tapatalk
Sent from my SM-S906U using Tapatalk
- propane1
- Posts: 2465
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5847 times
- Been thanked: 8898 times
- DavidBarkey
- Posts: 3175
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 17454 times
- Been thanked: 10775 times
- DavidBarkey
- Posts: 3175
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 17454 times
- Been thanked: 10775 times
- Eugen
- Posts: 5174
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 12134 times
- Been thanked: 16397 times
- Contact:
Re: k301 stalling
If it runs just a little more if you give it choke when it starts stumbling it could be fuel delivery.
More troubleshooting needed. When it restarts, is it only when cold or right after?
More troubleshooting needed. When it restarts, is it only when cold or right after?
Case 224, 444, 644, 680E
Kubota B26
Kubota B26
- propane1
- Posts: 2465
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5847 times
- Been thanked: 8898 times
-
- Posts: 1608
- Joined: Sat Apr 23, 2022 8:16 pm
- Location: Missouri
- Has thanked: 12301 times
- Been thanked: 7040 times
Re: k301 stalling
This sounds similar to the trouble I had with the Onan in the 648. Ran for about twenty minutes then stumbles and dies. Mine was fuel delivery. Bowl would go dry
- propane1
- Posts: 2465
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5847 times
- Been thanked: 8898 times
Re: k301 stalling
Any farther along with this trouble Dave. I was thinking the points plunger might be sticking when hot.
Noel
Noel
- DavidBarkey
- Posts: 3175
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 17454 times
- Been thanked: 10775 times
Re: k301 stalling
Rainy day today and shop full . I plan to run it tommorrow and do some testing when it stalls now that I have some tings to look at .
Dave
Mad Tractor Builder
Mad Tractor Builder