Hi Dave, well that one caught me too about 8 years ago! Spirol pins are a much heaver duty version of a spiral pin, at least that was told to me after I complained on one of the forums that I had the pin between the belt pulley and jack-shaft shear on my snow caster that I replaced with a standard spiral pin from, I think Harbor Freight, that almost immediately sheared a couple of times. I can attest to the fact there is most definitely a strength difference!
I only buy my spirol pins now from a Case/Ingersoll dealer...
Lets talk snowcaster inprovements
-
- Posts: 589
- Joined: Wed Apr 13, 2022 3:18 pm
- Location: Webster, NY
- Has thanked: 1102 times
- Been thanked: 2546 times
- DavidBarkey
- Posts: 3130
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 17206 times
- Been thanked: 10544 times
Re: Lets talk snowcaster inprovements
Double it up Ray . Put in the one you need and find another pin that you can drive tight inside that . Or see if you can buy a double spiral in that size .ras101 wrote: ↑Sun Mar 12, 2023 9:44 am Hi Dave, well that one caught me too about 8 years ago! Spirol pins are a much heaver duty version of a spiral pin, at least that was told to me after I complained on one of the forums that I had the pin between the belt pulley and jack-shaft shear on my snow caster that I replaced with a standard spiral pin from, I think Harbor Freight, that almost immediately sheared a couple of times. I can attest to the fact there is most definitely a strength difference!
I only buy my spirol pins now from a Case/Ingersoll dealer...
Dave
Mad Tractor Builder
Mad Tractor Builder
-
- Posts: 589
- Joined: Wed Apr 13, 2022 3:18 pm
- Location: Webster, NY
- Has thanked: 1102 times
- Been thanked: 2546 times
Re: Lets talk snowcaster inprovements
So what did you paint your auger with? Looking perhaps for a graphite paint? is something that is slick and long lasting. My auger has been sand blasted and totally bald at this time (not the one on my current snow caster..
- DavidBarkey
- Posts: 3130
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 17206 times
- Been thanked: 10544 times
Re: Lets talk snowcaster inprovements
Tremclad with urethane universal hardener in summer and allowed to fully cure before assembly(30 days ) . Has stood up very well .
Dave
Mad Tractor Builder
Mad Tractor Builder
-
- Posts: 323
- Joined: Sat Mar 06, 2021 3:09 pm
- Location: Houghton Lake, MI
- Has thanked: 16 times
- Been thanked: 1430 times
Re: Lets talk snowcaster inprovements
When I restored my caster, I too was debating which paint direction to go. I did my modifications and sanblasted everything. I then epoxy primed and initially was going to go with the graphite coating on the inside of the housing and auger. I decided not to and thought that it was going to be higher maintenance down the road. A few years ago I had a ice fishing auger I cleaned up and graphite coated and it needed several coats to cover. I've used that ice auger alot and ice clings to it often. That's the reason I decided to spray it all with oem paint. I'm happy I did. I feel the nice smooth coat of paint does great. I plan on putting a coat of polish and wax on it this summer just because I feel the ice will just continue to slide right off. I can't wait to see your uhmw liner installed. I remember having a discussion a while back about doing the same. My only concern was water becoming trapped behind the uhmw and or the glue releasing. I am wondering if a rubber paddle would be necessary once the uhmw is. I've had a few casters before settling on restoring the one I have now. I went through them all and the gap at the center throwing portion of the auger had varied alot.
Sent from my SM-S906U using Tapatalk
Sent from my SM-S906U using Tapatalk
- Eugen
- Posts: 5160
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 12037 times
- Been thanked: 16297 times
- Contact:
Re: Lets talk snowcaster inprovements
I just used quality implement paint. Ugliest colour ever, a brownish black. Painted with a brush this Fall, after some wire brush cleaning. The snow does not stick to it. I meant it more as protection, as the auger and interior side of the caster were quite rusty. I'm amazed how well it did so far though. Anything you do should probably be better than I did.
Case 224, 444, 644, 680E
Kubota B26
Kubota B26
-
- Posts: 146
- Joined: Sun Mar 21, 2021 8:03 pm
- Location: Hemlock, MI
- Has thanked: 12 times
- Been thanked: 474 times
Re: Lets talk snowcaster inprovements
If you need to open the hood and not have it hit the caster chute you just have to drive the front tires up some ramps or jack it up and add blocks. Then you can lower the caster more. I know it was too easy. But, most of the time your mind is on what is under the hood.