Kingpin to bell crank arm attachment
- thebuildist
- Posts: 818
- Joined: Mon Jul 26, 2021 5:09 pm
- Location: Atlanta, ga
- Has thanked: 839 times
- Been thanked: 3270 times
Kingpin to bell crank arm attachment
Advice question: When I built my new front axle, I located the bell cranks, (aka the steering arms) up on top of the axle, on the upper side of the kingpin.
The hydraulic steering cylinder itself is attached to a steering arm down under the axle, at the bottom of the kingpin.
So, on the right side, the hydraulic steering cylinder moves the lower steering arm, and the righthand hub/spindle assembly with it.
When the righthand hub spindle pivots, the kingpin turns the right hand upper bell crank (steering arm), and that's attached to the tie rod, and the tie rod makes the lefthand bellcrank/steering arm move, so both steering spindles pivot together.
The upper bellcrank/steering arm is attached to the kingpin with a 1/4" roll pin.
Today the righthand roll pin apparently sheared off. Because the righthand spindle assembly and kingpin are moving, but the steering arm, and the whole lefthand spindle assembly are sitting still.
This makes it challenging to drive the tractor.
My engineering reference told me that that roll pin should have 4000 lbs of shear strength, which I thought would be more than plenty.
I apparently thought wrong.
The same part on whatever farm tractor has the steering arm attached/locked in place via a spline.
I presume I'm going to have to tear it apart and cut a spline on the kingpin and the inside bore of the upper steering arm.
That's going to be a REAL pain.
Any other ideas before I do all that work?
Bob
The hydraulic steering cylinder itself is attached to a steering arm down under the axle, at the bottom of the kingpin.
So, on the right side, the hydraulic steering cylinder moves the lower steering arm, and the righthand hub/spindle assembly with it.
When the righthand hub spindle pivots, the kingpin turns the right hand upper bell crank (steering arm), and that's attached to the tie rod, and the tie rod makes the lefthand bellcrank/steering arm move, so both steering spindles pivot together.
The upper bellcrank/steering arm is attached to the kingpin with a 1/4" roll pin.
Today the righthand roll pin apparently sheared off. Because the righthand spindle assembly and kingpin are moving, but the steering arm, and the whole lefthand spindle assembly are sitting still.
This makes it challenging to drive the tractor.
My engineering reference told me that that roll pin should have 4000 lbs of shear strength, which I thought would be more than plenty.
I apparently thought wrong.
The same part on whatever farm tractor has the steering arm attached/locked in place via a spline.
I presume I'm going to have to tear it apart and cut a spline on the kingpin and the inside bore of the upper steering arm.
That's going to be a REAL pain.
Any other ideas before I do all that work?
Bob
"Never be afraid to try something new. How hard can it be?"
- Spike188
- Posts: 1074
- Joined: Sat Mar 06, 2021 12:58 pm
- Location: Ayr Ontario
- Has thanked: 5833 times
- Been thanked: 4144 times
Re: Kingpin to bell crank arm attachment
I was thinking a 6mm taper pin https://spaenaur.com/catalog/E92/ because they are rated at 72,000 psi but calculate back to a shear strength of 3,600 psi but 18-8 dowel pins https://spaenaur.com/catalog/E82/ might do the trick. I am spoiled because this company warehouse is 20 minutes from me and delivers for $5.00. McMaster Carr may have taper pins with better specifications. https://www.mcmaster.com/taper-pins/taper-pins-5/
A .250" grade 8 bolt would probably work better.
A .250" grade 8 bolt would probably work better.
Spike Colt - 9 & 10, Case - 108, 118, 444, 446, 448, 646, 646bh, Ingersoll 4016, 4118AH
- Spike188
- Posts: 1074
- Joined: Sat Mar 06, 2021 12:58 pm
- Location: Ayr Ontario
- Has thanked: 5833 times
- Been thanked: 4144 times
Re: Kingpin to bell crank arm attachment
There shear strength on a 1/4" grade 8 calculates out to approximatly 7,500 lbs.
Spike Colt - 9 & 10, Case - 108, 118, 444, 446, 448, 646, 646bh, Ingersoll 4016, 4118AH
-
- Posts: 1579
- Joined: Sat Apr 23, 2022 8:16 pm
- Location: Missouri
- Has thanked: 12139 times
- Been thanked: 6886 times
Re: Kingpin to bell crank arm attachment
Grade 8 bolt is what came to mind too. Be worth trying before taking it all apart. Or what about the possibility of opening the hole up and trying a grade 8 3/8-24 bolt? That would more than triple the shear strength of a 1/4 roll pin.
- propane1
- Posts: 2450
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5815 times
- Been thanked: 8806 times
Re: Kingpin to bell crank arm attachment
Are there grade 8 bolts smaller than 1/4” ? I have a place for that if there is such a thing. 3/16” is what I need.
Noel
Noel
- Spike188
- Posts: 1074
- Joined: Sat Mar 06, 2021 12:58 pm
- Location: Ayr Ontario
- Has thanked: 5833 times
- Been thanked: 4144 times
Re: Kingpin to bell crank arm attachment
Noel, a #10 grade 8 bolt is 3/16"
#10 bolts are theoretically 0.190" and 3/16 equals 0.187"
#10 bolts are theoretically 0.190" and 3/16 equals 0.187"
Spike Colt - 9 & 10, Case - 108, 118, 444, 446, 448, 646, 646bh, Ingersoll 4016, 4118AH
- thebuildist
- Posts: 818
- Joined: Mon Jul 26, 2021 5:09 pm
- Location: Atlanta, ga
- Has thanked: 839 times
- Been thanked: 3270 times
Re: Kingpin to bell crank arm attachment
It needs to have zero play, not so much as a wiggle. The roll pin, being spring loaded eliminated play. And a tapered pin would do the same.
But using a bolt is going to be tough. I could precision turn the bolt and ream the hole, but even then I think I'd need to use Loctite to eliminate play.
And that would make disassembly a nightmare.
And I'm afraid to drill it much larger than 1/4", as I'm concerned it could begin to weaken the 1" kingpin itself.
The thought occured to me to install two roll pins at right angles to each other, vertically separated by... 1/2 inch? I don't know how much separation I'd need to maintain the kingpin's strength/integrity. But I'd probalby need to pull the current kingpin and weld closed the existing hole and redrill altogether, because the current hole is right in the center of the bellcrank collar.
Bob
But using a bolt is going to be tough. I could precision turn the bolt and ream the hole, but even then I think I'd need to use Loctite to eliminate play.
And that would make disassembly a nightmare.
And I'm afraid to drill it much larger than 1/4", as I'm concerned it could begin to weaken the 1" kingpin itself.
The thought occured to me to install two roll pins at right angles to each other, vertically separated by... 1/2 inch? I don't know how much separation I'd need to maintain the kingpin's strength/integrity. But I'd probalby need to pull the current kingpin and weld closed the existing hole and redrill altogether, because the current hole is right in the center of the bellcrank collar.
Bob
"Never be afraid to try something new. How hard can it be?"
- Gordy
- Posts: 653
- Joined: Sat Mar 06, 2021 1:24 pm
- Location: MapleLake,MN
- Has thanked: 2343 times
- Been thanked: 2136 times
Re: Kingpin to bell crank arm attachment
How about a spirol pin? 1/4" OD and 7,800 Lbs.
https://www.zoro.com/zoro-select-spring ... TCEALw_wcB
Gordy
https://www.zoro.com/zoro-select-spring ... TCEALw_wcB
Gordy
- Eugen
- Posts: 5166
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 12099 times
- Been thanked: 16346 times
- Contact:
Re: Kingpin to bell crank arm attachment
I have a different question for you guys: should there ever should be more than 4000 lbs force on that pin? Under normal circumstances the only force opposing the steering force is the front tires friction on the surface of the soil. I have serious doubts that opposing force is anywhere near 4000 lbs.
I'd double check the range of movement of the wheels against the full range of movement of the steering cylinder. Even a little discrepancy would cause that pin to sheer.
If that checks out my second theory is that the pin was maybe of lesser quality and nowhere near the 4000 lbs rating.
I'd double check the range of movement of the wheels against the full range of movement of the steering cylinder. Even a little discrepancy would cause that pin to sheer.
If that checks out my second theory is that the pin was maybe of lesser quality and nowhere near the 4000 lbs rating.
Case 224, 444, 644, 680E
Kubota B26
Kubota B26
- propane1
- Posts: 2450
- Joined: Thu Dec 23, 2021 11:32 am
- Location: PEI, Canada
- Has thanked: 5815 times
- Been thanked: 8806 times