Linde 225 MIG welder in bad shape

Discussions with more focus on welding.
User avatar
Spike188 Canada
Posts: 1058
Joined: Sat Mar 06, 2021 12:58 pm
Location: Ayr Ontario
Has thanked: 5602 times
Been thanked: 4041 times

Re: Linde 225 MIG welder in bad shape

Post by Spike188 »

Just makes you want to spit and spew when that happens. Better luck on the next round. I didn't do the math but with larger capacity caps installed, can you get by with 3 caps?
Spike Colt - 9 & 10, Case - 108, 118, 444, 446, 448, 646, 646bh, Ingersoll 4016, 4118AH
User avatar
Eugen Canada
Posts: 5141
Joined: Wed Mar 03, 2021 2:52 pm
Location: Port Mcnicoll, Ontario
Has thanked: 11934 times
Been thanked: 16195 times
Contact:

Re: Linde 225 MIG welder in bad shape

Post by Eugen »

Spike188 wrote: Fri Oct 21, 2022 1:52 pm Just makes you want to spit and spew when that happens. Better luck on the next round. I didn't do the math but with larger capacity caps installed, can you get by with 3 caps?
True! Yes, the forth one even didn't behave that nicely when I reformed it. It was hungry to draw a lot of current for too long, instead of charging nicely. Anyway, the three of them left are 16,000uF each, which is just 2000uF less than the original total capacity. And they didn't get warm at all while testing the welder on scrap.

So, yes, I decided to hook it up to welding gas and give it a proper try. Tested this MIG welder on various heat and wire speed settings and it sparkles just fine. The only slight problem is that the wire gets occasionally stuck in the cable of the gun. It's the only solid wire I got now (0.035), is rusty, and the gun and cable are really beat up, so this requires some attention.

However, right now it looks like this Linde 225 MIG welder has been saved from scrap and this makes me quite content. :highfive:
Case 224, 444, 644, 680E
Kubota B26 :blush:
User avatar
DavidBarkey Canada
Posts: 3108
Joined: Sat Mar 06, 2021 10:35 am
Location: Waverley On.
Has thanked: 17070 times
Been thanked: 10413 times

Re: Linde 225 MIG welder in bad shape

Post by DavidBarkey »

You will have a real nice welder when you are done .
Dave
Mad Tractor Builder
Jancoe United States of America
Posts: 323
Joined: Sat Mar 06, 2021 3:09 pm
Location: Houghton Lake, MI
Has thanked: 16 times
Been thanked: 1428 times

Re: Linde 225 MIG welder in bad shape

Post by Jancoe »

Just a little tip for the mig welder. Seeing how you have some rusty wire. I use a clip on wire cleaner. You could use just about anything like foam ear plugs or felt with a paper clamp. Keeping the debris out of the liner is the goal. Hope this helps. Image

Sent from my SM-S906U using Tapatalk

User avatar
Eugen Canada
Posts: 5141
Joined: Wed Mar 03, 2021 2:52 pm
Location: Port Mcnicoll, Ontario
Has thanked: 11934 times
Been thanked: 16195 times
Contact:

Re: Linde 225 MIG welder in bad shape

Post by Eugen »

Thank you @Gordy !


DavidBarkey wrote: Fri Oct 21, 2022 5:18 pm You will have a real nice welder when you are done .
Yes Dave, I think you're right. I must say right now it seems a little too sophisticated a device for a beginner like me. I felt very comfortable with the stick welder and if I convert it to DC it'll probably be even nicer. So... :hm:
Case 224, 444, 644, 680E
Kubota B26 :blush:
User avatar
Harry United States of America
Posts: 1483
Joined: Sun Mar 07, 2021 8:33 am
Location: Lockport,NY
Has thanked: 9159 times
Been thanked: 6197 times

Re: Linde 225 MIG welder in bad shape

Post by Harry »

I have seen a scotch brite pad held on the wire with a clip to take the rust of the wire.

Keep the :peace: :cop:
Harry
1973 444, 1974 644, 1976 446, 1977 646, 1986 226
User avatar
DavidBarkey Canada
Posts: 3108
Joined: Sat Mar 06, 2021 10:35 am
Location: Waverley On.
Has thanked: 17070 times
Been thanked: 10413 times

Re: Linde 225 MIG welder in bad shape

Post by DavidBarkey »

Harry wrote: Sun Oct 23, 2022 4:52 pm I have seen a scotch brite pad held on the wire with a clip to take the rust of the wire.

Keep the :peace: :cop:
Harry
I do the same with a piece of rag to keep the wire clean . Does a good job .
Dave
Mad Tractor Builder
Post Reply