Pictures: this moment
-
- Posts: 1793
- Joined: Sat Apr 23, 2022 8:16 pm
- Location: Missouri
- Has thanked: 13562 times
- Been thanked: 7923 times
Re: Pictures: this moment
I couldn’t help but pull through the equipment dealers lot and do some daydreaming. Sure are some nice shiny things here I’d love to play with!
- DavidBarkey
- Posts: 3426
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 18666 times
- Been thanked: 11974 times
Re: Pictures: this moment
A line from the Andy Griffen show about letting Opie chose for himself come to mind here . ooouuuu shinny .
Dave
Mad Tractor Builder
Mad Tractor Builder
-
- Posts: 1793
- Joined: Sat Apr 23, 2022 8:16 pm
- Location: Missouri
- Has thanked: 13562 times
- Been thanked: 7923 times
Re: Pictures: this moment
That was a great show! I still turn it on and watch and laugh!DavidBarkey wrote: ↑Fri May 03, 2024 1:14 pmA line from the Andy Griffen show about letting Opie chose for himself come to mind here . ooouuuu shinny .
-
- Posts: 5280
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 12888 times
- Been thanked: 16930 times
- Contact:
Re: Pictures: this moment
Argh! My dear 644 which I just wanted to put for sale shows a small hydraulic oil leak at the pump. Cannot sell it like that so the engine needs to move forward and the pump to come out.
-
- Posts: 1793
- Joined: Sat Apr 23, 2022 8:16 pm
- Location: Missouri
- Has thanked: 13562 times
- Been thanked: 7923 times
Re: Pictures: this moment
That’s not the way it’s supposed to go!
Hopefully it won’t be to bad to repair.
-
- Posts: 5280
- Joined: Wed Mar 03, 2021 2:52 pm
- Location: Port Mcnicoll, Ontario
- Has thanked: 12888 times
- Been thanked: 16930 times
- Contact:
- Spike188
- Posts: 1195
- Joined: Sat Mar 06, 2021 12:58 pm
- Location: Ayr Ontario
- Has thanked: 7259 times
- Been thanked: 4721 times
Re: Pictures: this moment
@Eugen Those look like "cold" casting marks where the molten metal enters a mould from multiple headers and vents. In most cases they do not effect the integrity of the part. Experience has taught me that when cold joints are failures it will be in multiple castings. Setting up a bench test with the pump out of the tractor should not be to hard. I had several @thebuildist moments this week. In one instance a tool chuck was closed minus the tool causing the collet to jam. Procedure for clearing the jam is removing the 1700 psi pump and connecting a 10 ton hand pump. In this case 3000 psi was not adequate for releasing the jam. I entionality put 5000 psi to the cylinder, ruining the 3000psi gage and creating a fear that internal seals may have failed after over pressure. Further testing proved that stroke adjustment was the root cause of all the issues. Yes there was sweat.
Spike Colt - 9 & 10, Case - 108, 118, 444, 446, 448, 646, 646bh, Ingersoll 4016, 4118AH
- DavidBarkey
- Posts: 3426
- Joined: Sat Mar 06, 2021 10:35 am
- Location: Waverley On.
- Has thanked: 18666 times
- Been thanked: 11974 times
Re: Pictures: this moment
@Eugen . Was there any oil residue in the inside of the pump mount bracket ? If so change the front shaft seal.
Dave
Mad Tractor Builder
Mad Tractor Builder
- MattA
- Posts: 1025
- Joined: Sun Mar 07, 2021 1:57 pm
- Location: Swansea MA
- Has thanked: 3 times
- Been thanked: 4496 times
Re: Pictures: this moment
Bought it
At some point I'll start work on a mount to the mule drive.
Both linear actuators work. The bucket dump actuator has a clutch when it hits the end of its range. The lift probably does but I can't test that without the actuator mounted on both ends.
The bucket is actually small enough that I've got it on a shelving rack in my garage with the mount removed.
At some point I'll start work on a mount to the mule drive.
Both linear actuators work. The bucket dump actuator has a clutch when it hits the end of its range. The lift probably does but I can't test that without the actuator mounted on both ends.
The bucket is actually small enough that I've got it on a shelving rack in my garage with the mount removed.
Ingersoll 4016
-
- Posts: 1793
- Joined: Sat Apr 23, 2022 8:16 pm
- Location: Missouri
- Has thanked: 13562 times
- Been thanked: 7923 times
Re: Pictures: this moment
Congratulations @MattA , glad you got it!
I’m looking forward to seeing it get mounted on your tractor and going to work!
I’m looking forward to seeing it get mounted on your tractor and going to work!